<ins id="qhx66"></ins>

    <output id="qhx66"><track id="qhx66"></track></output><tr id="qhx66"></tr>
    <code id="qhx66"></code>
    <code id="qhx66"></code><code id="qhx66"><acronym id="qhx66"></acronym></code>
    ?

    全国服务热线:

    15853163650
    您当前的位置:首页 > 新闻动态 > 行业新闻
      联系我们

      CONTACTS US

      地址:山东济南历城区华龙路嘉恒大厦A座1201室

      邮箱:hhjc168@126.com

      公司传真: 0531-88518398

      电话:15853163650

    行业新闻

    COMPANY NEWS

    石塑UV板花线条的加工制作工艺

    2016-06-03 16:23:05 文章来源:www.crbanking.com

    1、用成型铣磨轮直接加工。这是石塑UV板加工花线使用最多的,也是最经济、加工效率最高的方法。它对花线凹凸起伏不大的形状加工较快。这需要事先做出与要加工花线凹凸正相反的铣磨工具,在石塑UV板线条机上磨出曲线来,磨轮要准备粗磨、精磨、抛光三种,依次使用即可。
    1, with the forming mill wheel direct processing. This is the stone plastic processing thread UV board using the most, is the most economical, the highest efficiency of processing method. It is not on the yarn bump and shape processing faster. This requires prior to processing yarn irregularities on the contrary of milling tool, in the stone plastic UV board molding machine grinding curves to grinding wheel to prepare rough grinding, fine grinding, polishing of three, which in turn can be used.
    2、先用金刚石圆锯片粗加工,再用铣磨轮精加工、抛光。这种方法适合花线凹凸起伏比较大的那些宽或窄的形状。如果用铣磨轮直接加工磨耗量大,而用切割效率比较高的圆锯片先行去掉大部分多余的料后,再用铣磨轮粗磨、精磨、抛光即可。 也可使用多用铣磨线条机解决此类加工。

    电梯门套
    2, first with a diamond saw blade with rough machining, milling grinding wheel finishing and polishing. Those wide or narrow the shape of this method is suitable for large bump and yarn. If milling grinding wheel directly processing the amount of wear large, and relatively high cutting efficiency of the circular saw blade first remove most of the excess material, and then milling grinding round rough grinding, fine grinding, polishing can. It can be used to solve this kind of processing with the multi - milling machine.
    3、用金刚石串珠锯切割,再经过仿型机磨抛或手动抛光。这适合加工比较宽大的石塑UV板花线,切割可同时获得凹、凸两种花线,如设计得好,两种花线都可在一个工程上使用,利于节约成本。 石塑UV板花线条所应具有的物理力学性能:密度不低于2.6g/cm3,吸水率小于0.75,干燥压强大于20mpa,弯曲强度大于7mpa。
    3, using diamond wire saw cutting, grinding and polishing after copying machine or manual polishing. This is suitable for processing of the relatively large stone plastic UV board flex, cutting and concave and convex two kinds of yarn, such as design, two kinds of flowers line can be used in a project, can save the cost. The physical and mechanical properties of stone plastic UV board flower lines should be: the density is not less than 2.6g/cm3, the water absorption rate is less than 0.75, the dry pressure is greater than 20MPa, the bending strength is greater than 7mpa.
    本文由电梯门套提供帮助,更多的相关内容请点击:http://www.crbanking.com我们将详情为您解答.欢迎您的光临!
    The elevator door to provide help, more relevant content please click: http://www.crbanking.com us the details for you to answer. Welcome your presence!

    ope体育